![]() Confirm this by ensuring that the button just below the lower left corner of the waterfall pane reads "WF" if it does not, click it until it does.) (This pane can actually display things other than the waterfall, but this training course will assume you are seeing the waterfall. As seconds pass, each signal appears at the top of the waterfall and disappears at the bottom. Here, incoming and outgoing digital signals are displayed. Below the transmit pane, with a black background by default, is the waterfall pane. It will display in black any text that is set up to be transmitted and in red any text that has already been transmitted during the current transmit session. Below the contact pane, with a pale blue background by default, is the transmit pane. It retains that text during your current fldigi session but is erased when you close fldigi (though it is saved in your log files). It will show pretty much everything that happens during your fldigi session, including text you have received and text you have transmitted. The upper large horizontal pane, with a pale yellow background by default, is the receive pane (or contact pane). (Your copy of fldigi may look a little different the user interface can be modified in many ways!) Note the three large horizontal panes and one vertical pane: Pressing the button disables the count and restores fldigi to normal keyboard operation.Now, with any interface device and cables disconnected from your computer, launch fldigi as you would any other newly-installed application. This button shows the count-down to the next transmission. This is the count-down timer button that is enabled when a macro button has been configured to repeat after a specified number of seconds. The right most button is normally not visible. The peak-to-peak amplitude of this tone is the standard by which you should set your transmitter drive or adjust your antenna matching network. ![]() Tune button - toggles the "Tune" mode which causes fldigi to insert a tone at the current waterfall frequency. TxID button - toggles the transmission of the RSID signal. ![]() RxID button - toggles the detection of Reed Solomon Identification codes. The main window text is not searched if the viewer is active, i.e., if it is displayed and the current modem is PSK. It is automatically turned off when playback is selected in the Files menu. Use this button to toggle the callsign spotting reporter on and off. Spot button - The "Spot" light button is visible if callsign spotting is enabled. fldigi silently opens a download web site, checks and reports on whether a new version is available.Ībout - Version number and a little about the programmers This is a useful window for reporting problems with the program to the developers.Ĭheck for updates. open up browser to the web page preset to your callsignĬommand line options - display a list of all command line switches available to the fldigi userĪudio device info - displays information about all audio devices detected on the computer systemīuild info - displays all relevant information regarding the compilation and link for the applicationĮvent log - opens a text display window that records various events depending on the level of reporting depth selected. open up default browser to the primary web page ![]() open up default browser to the on-line Help siteįldigi web site. Min WF Controls - toggles the visibility of various waterfall controls as configured by the user None - removes the Rig Control / Log panel from the main User Interfaceĭocked scope - toggles the visibility of the docked scope display to the right of the waterfall Partial - reduce number of rig and logging controls to those essential for normal QSO or contest Weather Fax Image TX - Opens WEFAX transmit dialog Weather Fax Image RX - Opens WEFAX receive dialog IFKP Raw Image - Opens the IFKP picture image (if being received) THOR Raw Image - Opens the THOR picture image (if being received) MFSK Image - Opens the MFSK picture image (if being received) Spectrum scope- Opens the spectrum analysis dialog View/Hide 48 macros - toggle display of 4 rows of macrosįloating Scope - Opens a resizable, moveable scope display Signal browser - open the psk/rtty viewer dialog to display up to 30 simultaneously decoded psk signals Dialog viewer contains shared data / control with the View/Hide Channel viewer View/Hide Channels - Opens / Closes muli-signal viewer, shares space with Rx/Tx panels
0 Comments
Leave a Reply. |